--> 5580 automatic vacuum skin packaging machine common faults and troubleshooting methods-Fengyuan Packaging_Skin Packaging Film_Surlyn Film

All
  • All
  • Product Management
  • News
  • Introduction
  • Enterprise outlets
  • FAQ
  • Enterprise Video
  • Enterprise Atlas

5580 automatic vacuum skin packaging machine common faults and troubleshooting methods


Fengyuan Brand (Fengyuan Brand) 5580 Skin Packaging Machine is an automatic normal heating type (direct heating) vacuum skin packaging machine. Processing plant favorite. This machine uses high quality parts, exquisite manufacturing technology, and very low failure rate. Today, the Fengyuan Packaging Information Department will talk about the common faults and troubleshooting methods of the 5580 automatic vacuum skin packaging machine, hoping to help everyone.

 

The 5580 skin-packing machine uses a direct heating system. The heating tube is a black ceramic tube, which is very durable. If uneven heating is found, check the heating tube for damage. The troubleshooting method is: turn on the heating system to heat, and then roll the skin-packed film into a small tube to touch each heating tube. If a heating tube contacts the film roll and does not melt, it is the The heat pipe is broken, just replace it according to the connection.

 

The hot box of the 5580 body-fit vacuum packaging machine uses the front-to-back moving type. If the hot box moves to the front end, the film frame does not fall and there is no subsequent vacuum action. The reason for this failure is that the hot box does not touch the front end when the hot box moves Switch (LIMIT SWITCH), just replace it.

 

5580 automatic vacuum skin packaging machine common faults and troubleshooting methods

 

The skin-packaging film peeled off in the sandwich frame, resulting in poor vacuum. Check the fit of the upper and lower membrane frames. If it's loose, take care of it. You can improve this by placing a few thin pieces of paper under the sandpaper.

 

The sandwich frame cannot rise. Check several travel switches on the drive shaft in the body. Please adjust to the appropriate position according to the instructions.

 

Vacuum system. If you find that the vacuum suction is suddenly weak, or the sound of the vacuum pump suddenly changes, it is to remind the vacuum pump that it is broken, check and replace it.

 

Well, the above is the sharing of the common faults and troubleshooting methods of 5580 automatic vacuum body packaging machine by Fengyuan Body Packaging Information Department. If you find this article helpful, please pay more attention to our news release in the future.

 

Guangdong Fengyuan Packaging, a well-known Guangdong skin-packing company, creates aesthetic value of skin-packing,

 

Original articles, plagiarism must be legally responsible.

 

Technical Support


The main types of sarin film (DuPont sand shower body film) and how to choose it?

The main types of sarin film (DuPont sand shower body film) and how to choose it?


Commercial value of sand leaching film (dupont sarin film) in hardware packaging

What are the commercial values ​​of sand shower film advantages (advantages of Dupont sarin film) in skin packaging for hardware products ?


Shalin film (dupont sarin body film, sand shower film) suitable for packaging high-end hardware products

Is sarin film (dupont sarin body film, sand shower film) suitable for packaging high-end hardware products?


Well-known sarin film manufacturer-Guangdong Fengyuan Skin Packaging Factory  

Dongguan Zhongtang Fengyuan Packaging Products Factory is a well-known domestic manufacturer of sarin film .


What is the process principle of SE body packaging film (SE body film)?

Skin-packing process: The transparent skin-packaging film is properly heated and softened and then covered on the product and the bottom plate. At the same time, vacuum suction is enabled under the bottom plate of the close-pack packaging machine. The body-fitting film is adhered to the bottom plate (color printing paper card, corrugated cardboard or foam cloth, etc.)


What is the process principle of SE body packaging film (SE body film)?

After the transparent skin packaging film is properly heated and softened, it is covered on the product and the bottom plate, and the vacuum suction is enabled under the chassis. The body-fitting film is formed and stuck on the chassis (color printing paper card, tile edge board or bubble cloth, etc.).


What is the process principle of PET skin packaging film (PET skin film)?

What is the process principle of PET skin packaging film (PET skin film)? PET skin-packing film (PET skin-packing film) is a plastic film used for skin-packaging made of PET plastic material extruded into a film and then coated with hot melt glue.


What is the process flow of PE skin packaging film (PE skin film)?

What is the process flow of PE skin packaging film (PE skin film)? The transparent PE body packaging film (PE body film) is properly heated and softened, and then covered on the product and the bottom plate.


What is the principle of the PVC body packaging film (PVC body film)?

What is the principle of the PVC body packaging film (PVC body film)? The transparent PVC body packaging film (PVC body film) is appropriately heated and softened, and then covered on the product and the bottom plate.


Vacuum body-fitting film (vacuum body-packing film) has many advantages to ensure the perfect fit of circuit board magnetic core hardware products

Vacuum body-fitting film ( vacuum body-packing film ) has many advantages to ensure the perfect body-fitting of circuit board magnetic core hardware products: good toughness, resistance to handling and low temperature Good transparency, fresh and bright after packaging.


What are the main features and advantages of vacuum body film (vacuum body film)?

What are the main features and advantages of vacuum body film (vacuum body film)?


What are the main uses of PET body film (PET body packaging film)?

What are the main uses of PET skin pack film ( PET skin pack film )? Hardware products (furniture hardware, decorative hardware, etc.), auto / motorcycle accessories (such as brake pads, gears), measuring tools (drills, saw blades, etc.), stationery, toys, sports equipment / furniture accessories, pneumatic / hydraulic accessories, crafts, Ceramic / Glass products.