--> Reasons and solutions for vacuum suction failure of seafood food packaging machine-Fengyuan Packaging_Skin Packaging Film_Surlyn Film

All
  • All
  • Product Management
  • News
  • Introduction
  • Enterprise outlets
  • FAQ
  • Enterprise Video
  • Enterprise Atlas

Reasons and solutions for vacuum suction failure of seafood food packaging machine


Foods such as cold seafood and fresh meat have very high vacuum requirements for vacuum skin packaging. When our factory is using the vacuum packaging machine for seafood, sometimes we may encounter that the vacuum packaging of the seafood food packaging machine is not tight, or the vacuum suction of the skin packaging machine is small, the skin packaging machine foams, and the skin The packaging machine is not tightly attached, or the food vacuum packaging film is not tightly attached. What are the causes of such failures? And what is its solution? Today, Guangdong Refengyuan Packaging Information Department uses more than ten years of Fengyuan vacuum skin packaging machine manufacturing experience to tell you how to solve the problem of vacuuming.

 

1. When the vacuum pump of the seafood food vacuum packaging machine is evacuated to the maximum value, cut off the power supply. We need to watch whether the pointer of the barometer goes back. If so, it is leaking. You need to check where the leak is and then fix it.

 

2. Check whether the sealing strip around the vacuum chamber is damaged. In some cases, the vacuum pressure is insufficient, and the food packaging film and the food packaging box (fitting box) on the bottom are not sticky.

 

3. Check if there is any air leakage in the cylinder hole of the vacuum chamber. If available, seal the leak with a sealant.

 

4. Check if there is air leakage in the place where the wires go out of the heating plate. If necessary, block it with a sealant.

 

Vacuum suction packaging machine for seafood

 

Packaging effect of seafood and aquatic product skin packer with strong vacuum suction

 

Bubble-free effect of seafood food skin packaging machine

The above are the causes and troubleshooting methods of the vacuum suction packaging machine for seafood (not tight vacuum packaging, the vacuum suction force of the skin packaging machine is small, and the skin packaging machine is blistering). I hope I can help everyone.

 

Fengyuan Skin Packaging, a well-known Guangdong seafood food packaging company, creates aesthetic value for seafood food packaging.

 

Original articles, plagiarism must be legally responsible.

 

Technical Support


The main types of sarin film (DuPont sand shower body film) and how to choose it?

The main types of sarin film (DuPont sand shower body film) and how to choose it?


Commercial value of sand leaching film (dupont sarin film) in hardware packaging

What are the commercial values ​​of sand shower film advantages (advantages of Dupont sarin film) in skin packaging for hardware products ?


Shalin film (dupont sarin body film, sand shower film) suitable for packaging high-end hardware products

Is sarin film (dupont sarin body film, sand shower film) suitable for packaging high-end hardware products?


Well-known sarin film manufacturer-Guangdong Fengyuan Skin Packaging Factory  

Dongguan Zhongtang Fengyuan Packaging Products Factory is a well-known domestic manufacturer of sarin film .


What is the process principle of SE body packaging film (SE body film)?

Skin-packing process: The transparent skin-packaging film is properly heated and softened and then covered on the product and the bottom plate. At the same time, vacuum suction is enabled under the bottom plate of the close-pack packaging machine. The body-fitting film is adhered to the bottom plate (color printing paper card, corrugated cardboard or foam cloth, etc.)


What is the process principle of SE body packaging film (SE body film)?

After the transparent skin packaging film is properly heated and softened, it is covered on the product and the bottom plate, and the vacuum suction is enabled under the chassis. The body-fitting film is formed and stuck on the chassis (color printing paper card, tile edge board or bubble cloth, etc.).


What is the process principle of PET skin packaging film (PET skin film)?

What is the process principle of PET skin packaging film (PET skin film)? PET skin-packing film (PET skin-packing film) is a plastic film used for skin-packaging made of PET plastic material extruded into a film and then coated with hot melt glue.


What is the process flow of PE skin packaging film (PE skin film)?

What is the process flow of PE skin packaging film (PE skin film)? The transparent PE body packaging film (PE body film) is properly heated and softened, and then covered on the product and the bottom plate.


What is the principle of the PVC body packaging film (PVC body film)?

What is the principle of the PVC body packaging film (PVC body film)? The transparent PVC body packaging film (PVC body film) is appropriately heated and softened, and then covered on the product and the bottom plate.


Vacuum body-fitting film (vacuum body-packing film) has many advantages to ensure the perfect fit of circuit board magnetic core hardware products

Vacuum body-fitting film ( vacuum body-packing film ) has many advantages to ensure the perfect body-fitting of circuit board magnetic core hardware products: good toughness, resistance to handling and low temperature Good transparency, fresh and bright after packaging.


What are the main features and advantages of vacuum body film (vacuum body film)?

What are the main features and advantages of vacuum body film (vacuum body film)?


What are the main uses of PET body film (PET body packaging film)?

What are the main uses of PET skin pack film ( PET skin pack film )? Hardware products (furniture hardware, decorative hardware, etc.), auto / motorcycle accessories (such as brake pads, gears), measuring tools (drills, saw blades, etc.), stationery, toys, sports equipment / furniture accessories, pneumatic / hydraulic accessories, crafts, Ceramic / Glass products.